![utube mannlicher schoenauer rifle utube mannlicher schoenauer rifle](https://i.pinimg.com/736x/bf/26/0a/bf260a48b9f01df4ffe53554ccaf7cee--puch-steyr.jpg)
![utube mannlicher schoenauer rifle utube mannlicher schoenauer rifle](https://images.guns.com/prod/2020/12/05/5fcbd29ab7def04d85a60ca541b1f4f6410f758e4f439.jpeg)
When the striker is cocked, the thumb piece is pointing to the left.
![utube mannlicher schoenauer rifle utube mannlicher schoenauer rifle](https://i.ytimg.com/vi/GOw6H-54OvE/maxresdefault.jpg)
This safety bolt is operated by a customary thumb piece. Details of the cocking piece, safety and cocking piece nut construction may be seen. Pushing its rear end in permits withdrawal of the bolt. The pivoted lever at the left side of the receiver is the bolt release. When pressed it perm its the magazine spring to turn the rotary follower and expel any cartridges which may be in the magazine. The corrugated button on the right receiver side wall is a magazine release. Guides are machined into the front faces of the receiver bridge. Note that unlike other Mannlichers (except the Hungarian-made M 98/40 series) this rifle may be loaded from a charger clip. ^Ĭreek Mannlicher Schoenauer, action open ready for loading. The magazine is the rotary Schoenauer type. The ^ receiver bridge is split and the bolt handle locks down forward of the bridge. This is a turn-bolt design with Mannlicher two-piece bolt. This model and ils earlier variant the M 1903 arc military versions of ^ the common MS sporting 63mm (or 6.7mm).
#Utube mannlicher schoenauer rifle manual
A rib on the cocking piece is bored out from the rear to receive the spindle of the manual safety bolt.Ĭreek Mannlicher Schoenauer Model 03/14 Carbine, caliber 6.5mm. Its stud travels in the groove in the receiver tang where it engages with the sear nose. The cocking piece secured to the rear of the striker is prevented from turning by the end of its lock screw bearing on the flat on the striker. The flat 011 the striker working in the slot in the bolt head, prevents the cocking piece from turning as the bolt is turned up and drawn to the rear. The front end of the mainspring bears against the striker collar. The striker head has interrupted rings to permit attaching it to the striker. The spring extractor fits into a groove in the side of the bolt head, while a stud on the ejector lies in an undercut groove in the head. An escape hole is bored in the bolt cylinder to allow escape of any gas which might blow back due to a defective primer or cartridge head. When the bolt handle is drawn back, the cocking piece stud rests in a shallow groove in the rear of the bolt cylinder.Īlso at the rear end of the bolt is a recess to engage the end of the spindle of the manual safety. The striker hole is bored with interrupted rings by which the cocking piece is fastened to the striker. The lower side of the top rib of the cocking piece itself is cut out on the right side to clear a stop stud on the bolt. There is a cam shaped recess provided at the rear of the cylinder to receive the stud on the cocking piece as the arm is fired. A strengthening rib is provided in line with the bolt handle it is milled out. This handle turns down into a cut in the right side of the receiver. The bolt handle projects about of the distance from the rear of the cylinder and has a large knob which is bored out to make it lighter. This design has two locking lugs on opposing sides near the front of the bolt cylinder, but due to the removable bolt head they are placed farther back along the cylinder than in Mauser practice. There are tenons and slots for the flats on the forward end of the striker provided within the hollow bolt cylinder. The bolt head can be withdrawn only when the studs are turned so they are opposite their clearances. The bolt head has tenons fitting into the end of the bolt cylinder which work in circular grooves on the inside to lock the head. The bolt cylinder is bored out from the front to accept the removable bolt head. The 30-06 is a caliber designed for bringing down larger game and the sling swivel studs on the 1952s stock are designed for easily bringing this rifle with you on a long hunt.This is a standard Mannlicher turn- bolt design. The walnut stock features checkering at the grip to ensure a secure grasp with every shot fired. A 20 barrel is adorned with iron sights while Pachmayr Tip Over scope mounts cradle a Kahles fixed power scope. The Mannlicher Schoenauer 1952 is a bolt-action rifle chambered in 30-06. Sling loops allow for easy installation of a sling, while a recoil pad cushions users' shoulders with each shot fired. The Mannlicher Schoenauer 1952 features a European walnut stock features checkering at the grip and forend to ensure users have a firm grasp on this rifle. A steel barrel is adorned with a two-leaf U-notch rear sight and a ramp mounted bead front sight, the receiver also accepts side scope mounts. The Mannlicher Schoenauer 1952 is a family of rotary-magazine fed bolt-action rifles chambered in a variety of calibers.